New method measures 3-D polymer processing precisely

New NIST method measures 3D polymer processing precisely
A 3D topographic image of a single voxel of polymerized resin, surrounded by liquid resin. NIST researchers used their sample-coupled-resonance photo-rheology (SCRPR) technique to measure how and where there material's properties changed in real time at the smallest scales during the 3D printing and curing process. Credit: NIST

Recipes for three-dimensional (3-D) printing, or additive manufacturing, of parts have required as much guesswork as science. Until now.

Resins and other materials that react under light to form polymers, or long chains of molecules, are attractive for 3-D printing of parts ranging from architectural models to functioning human organs. But it's been a mystery what happens to the materials' mechanical and flow properties during the curing process at the scale of a single voxel. A voxel is a 3-D unit of volume, the equivalent of a pixel in a photo.

Now, researchers at the National Institute of Standards and Technology (NIST) have demonstrated a novel light-based atomic force microscopy (AFM) technique—sample-coupled-resonance photorheology (SCRPR)—that measures how and where a material's properties change in real time at the smallest scales during the curing process.

"We have had a ton of interest in the method from industry, just as a result of a few conference talks," NIST materials research engineer Jason Killgore said. He and his colleagues have now published the technique in the journal Small Methods.

3-D printing, or additive manufacturing, is lauded for flexible, efficient production of complex parts but has the disadvantage of introducing microscopic variations in a material's properties. Because software renders the parts as thin layers and then reconstructs them in 3-D before printing, the physical material's bulk properties no longer match those of the printed parts. Instead, the performance of fabricated parts depends on printing conditions.

NIST's new method measures how materials evolve with submicrometer spatial resolution and submillisecond time resolution—thousands of times smaller-scale and faster than bulk measurement techniques. Researchers can use SCRPR to measure changes throughout a cure, collecting critical data for optimizing processing of materials ranging from biological gels to stiff resins.

The new method combines AFM with stereolithography, the use of light to pattern photo-reactive materials ranging from hydrogels to reinforced acrylics. A printed voxel may turn out uneven due to variations in light intensity or the diffusion of reactive molecules.

AFM can sense rapid, minute changes in surfaces. In the NIST SCRPR method, the AFM probe is continuously in contact with the sample. The researchers adapted a commercial AFM to use an ultraviolet laser to start the formation of the polymer ("polymerization") at or near the point where the AFM probe contacts the sample.

The method measures two values at one location in space during a finite timespan. Specifically, it measures the resonance frequency (the frequency of maximum vibration) and quality factor (an indicator of energy dissipation) of the AFM probe, tracking changes in these values throughout the polymerization process. These data can then be analyzed with mathematical models to determine material properties such as stiffness and damping.

The method was demonstrated with two . One was a polymer film transformed by light from a rubber into a glass. Researchers found that the curing process and properties depended on exposure power and time and were spatially complex, confirming the need for fast, high-resolution measurements. The second material was a commercial 3-D printing resin that changed from liquid into solid form in 12 milliseconds. A rise in resonance frequency seemed to signal polymerization and increased elasticity of the curing resin. Therefore, researchers used the AFM to make topographic images of a single polymerized voxel.

Surprising the researchers, interest in the NIST technique has extended well beyond the initial 3-D printing applications. Companies in the coatings, optics and fields have reached out, and some are pursing formal collaborations, NIST researchers say.

More information: Callie I. Fiedler-Higgins et al. Monitoring Fast, Voxel-Scale Cure Kinetics via Sample-Coupled-Resonance Photorheology, Small Methods (2018). DOI: 10.1002/smtd.201800275

Citation: New method measures 3-D polymer processing precisely (2018, October 9) retrieved 28 March 2024 from https://phys.org/news/2018-10-method-d-polymer-precisely.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Explore further

Efficient chain transfer for 3D-printing of tough photopolymers

36 shares

Feedback to editors